Work Plan for Raced Cars upon return Records or Report Required
Chassis:                                Motor:  
Date:                                      Track: Laps Completed: Parts Needed or
     
Next Race date                    Track Action Required Who?
     
1 Scale car as raced w/ correct stagger LF:             LR:          RF:           RR:    
2 Fill with Fuel Gallons:    
3 Scale Car full of Fuel LF:             LR:          RF:           RR:    
4 Measure Caster LF:                             RF:    
5 Measure Camber LF:                             RF:    
6 Measure Toe Total Toe:    
7 Measure Setback of Front LF:                             RF:    
8 Check Rear End for Position Left to Right:             Front-Back:    
9 Check Engine for signs of Leaks:  water, oil condition    
10 Check Tranny for Leaks condition    
11 Check Rear End for Leaks condition    
12 Check Fuel System For Leaks condition    
13 Check Oil line system for Leaks condition    
14 Check Clutch System for Leaks condition    
15 Check Brake System for Leaks condition    
16 Check Power Steering System for Leaks condition    
17 Clean Car- Wipe down Completely   Additional Work? Who
18 Vacuum interior      
19 Drain Engine Oil attach tag to indicate it is empty    
20 Drain Tranny Fluid attach tag to indicate it is empty    
21 Drain Rear End Fluid attach tag to indicate it is empty    
22 Drain Water attach tag to indicate it is empty    
23 Inspect /Pack Wheel Bearings LF:             LR:          RF:           RR:    
24 Inspect Calipers LF:             LR:          RF:           RR:    
25 Inspect Rotors LF:             LR:          RF:           RR:    
26 Inspect Drive Shaft and U-Joints condition    
27 Inspect /GreaseTie Rod Ends condition    
28 Inspect Spring Buckets and Jack Bolts LF:             LR:          RF:           RR:    
29 Inspect and Grease all Ball Joints wipe off all excess grease    
30 Inspect/Grease Upper and Lower Control Arms LF:                             RF:    
31 Tighten / Inspect Strut rod ends Left                             Right    
32 Check Engine Mounting System condition    
33 Check Truck Arm Pivots and Eccentric condition    
34 Check Axle U-Bolts for Cracks condition    
35 Check Axle Chains for Cracks condition    
36 Check Transmission Mount condition    
37 Check Battery water level / clean terminals      
38 Check all Power cables and ground posts      
39 Check MSD connections / tight clean Disconnect if welding is needed on car    
40 Check gage operation      
41 Check Fire System Pressure and Clean ends      
42 Check Fuel pressure hose      
43 Check Radio and antenna connections      
44 Ready for Body Repairs Notes / Comments for Body Shop    
45 Repair any Minor Sheet metal damage      
46 Check all windows and lexan      
47 check all air intake vent hoses      
48 check fuel filler snout and seal      
49 check fuel cell and box      
50 complete all body work      
51 paint      
52 Window Clips and tight  w/ locktite      
53        
54        
55 Ready for Next race Preperation Condition of System or Parts Action Needed? Who
56 Belt and harness      
57 Seat mounting      
58 Radio Box  Secure      
59 Brake Bias Smooth and Set      
60 Fire System cables free      
61 Install new Oil Filter write date on filter and initial    
62 Fill with Oil- Safety wire tank      
63 Fill Tranny with Fluid- Safety wire      
64 Install correct gear set note here what set installed >             <    
65 Fill Rear end with Fluid- Safety Wire      
66 Fill Power Steering Fluid- Safety Wire      
67 Fill with Water - do not wire yet      
68 Plug wires Tight/ Dist cap OK      
69 Fan in operating Condition      
70 Oil Cooler tight and Clean      
71 Headers tight and clean      
72 Install New Fuel Filter      
73 Throttle Linkage travel OK check air box clearance    
74 Throttle springs (2) ok      
75 Transmission smooth in all 4 gears      
76 Shifter Linkage all tight.smooth operation      
77 Brake Pads OK      
78 Shocks Tight and valved correctly LF:             LR:          RF:           RR:    
79 Bleed Brakes      
80 Bleed Clutch      
81 Exhaust mounted and tight      
82 Hood Pins Tight and Adjusted      
83 Trunk Pins Tight and Adjusted      
84 Spoiler at 60 degrees      
85 Brake air Hoses and Ducts installed      
86 Fresh air tube for Driver      
87 Fresh air tube for Driver Feet      
88 Oil Cooler Ducts installed      
89 Rear end Cooler Ducts in place      
90        
91 Set-up Procedure   Work Completed Who
92 Inflate tire to proper pressures LF:             LR:          RF:           RR:    
93 Check and adjust Stagger LF:             LR:          RF:           RR:    
94 Make sure it is full of fuel      
95 Rough in all chassis heights LF:             LR:          RF:           RR:    
96 Check Quarter panel Heights LR:                             RR:    
97 Put on Turn Plates to Set Caster/Camber LF:                              RF:    
98 String Front wheels Check Front and Rear Toe LF:             LR:          RF:           RR:    
99 Put on tire stands      
100 Set Pan Hard bar heights LR:                             RR:    
101 Set rear end square and set-back LR:                             RR:    
102 Put Car on Scales      
103 Rough in weights with jack screws LF:             LR:          RF:           RR:    
104 Re-check chassis heights LF:             LR:          RF:           RR:    
105 Finalize weights LF:             LR:          RF:           RR:    
106 Put Car back on Ground      
107 Check Quarter Panel heights LR:                             RR:    
108 Put back on Turn Plates check      
109 Check  adjust Caster/Camber LF:                              RF:    
110 String Front Straight- Lock Steering Shaft      
111 Raise Front to Set 'Bump' LF:                              RF:    
112 Put back down and set Toe      
113 Set front fenders  outside of front tires      
114 Trim Air dam and Side Skirts to height Front                  Left                    Right    
115 Set-up is Complete      
116 Measure and record Jack Screw Heights LF:             LR:          RF:           RR:    
117 Make sure all Lead is secure      
118 Truck arm eccentrics are tight and marked      
119 Double Check spoiler angle Degrees:    
120 A-Arm bolts and shims tight      
121 All tie rod and etc  safety wired      
122 Check Jam nuts on Pan Hard Bar      
123 Wax      
124 Ready to Load